Die Set Up, Performance Monitoring
The Quik-Learn automatic tonnage monitor is important for die setup, SPC work, quality assurance and effective monitoring. Protecting investments, reducing downtime and improving productivity and product quality are all benefits of using the Quik-Learn. The Quik-Learn tonnage and deviation monitor is easy-to-use and inexpensive. All of the operator information and controls are on the front panel. There is no need to study manuals or undergo extensive training.
The Quik-Learn can display the forming stroke in three ways:
| Standard | Option | |
| Left, right, &total tonnage display | ✓ | |
| Deviation from tonnage setup | ✓ | |
| Displays tons or percent deviation | ✓ | |
| High &low tonnage display | ✓ | |
| Target Tonnage Indicator lights | ✓ | |
| Capacity &working tonnage alarms | ✓ | |
| Low alarms may be disabled | ✓ | |
| Automatically sets benchmark tonnage | ✓ | |
| View calibration numbers | ✓ | |
| Percent of benchmark setpoints | ✓ | |
| Percent of capacity setpoints | ✓ | |
| Automatic Zero Balance | ✓ | |
| Displays alarm setpoints | ✓ | |
| Accepts two or four sensor inputs | ✓ | |
| Analog output jacks | ✓ | |
| Standard RS-485/232 serial port | ✓ | |
| Autolearn | ✓ | |
| Part counter or Reverse load | ✓ | |
| Key reset | ✓ | |
| Flushmount Kit | ✓ | |
| Time based signatures | ✓ | |
| Overload counts | ✓ | |
| Pressroom networking | ✓ |
| No. Of Channels | Two |
| Sensor Inputs | Full bridge strain gauge sensors 120 to 1000 ohms Up to (4) 350 ohm sensors |
| Sensor Excitation | Built-in 10VDC @ 125mA max (Short circuit protected) |
| Balance Range | +/- 1mV/V of offset |
| Gain Range | Low Gain = 0.568mV/V to 5.000mV/V High Gain = 0.057mV/V to 0.625mV/V |
| Analog Output | .25" stereo phono jack 2.5VDC @ Press Capacity |
| Accuracy | +/- 1% of full scale max |
| Non-linearity | +/- .1% of full scale max |
| Frequency Response |
Flat DC to 1KHz |
| Display | 3-1/2 digit display |
| Display Update | Every Stroke (up to 2 updates per second max) |
| Resolution | 1024 count |
| SPM | 400 SPM (threshold trigger) 2000 SPM (probe trigger) |
| Calibration Shunts | 1 Meg Ohm .1% precision resistor |
| Computer Interface |
RS-485 |
| Trigger | Probe or Threshold |
| Threshold Probe | Built-in voltage source (12VDC @ 45mA max) provides power for NPN or PNP proximity probes. Also supports limit switch, solid state or mechanical relays |
| Resolver Interface | No |
| Shutdown Relay | 10A @ 120VAC N.O. and N.C. Contact Bypass switch available |
| Power Req. | 23 Watts max, 85-132VAC @ 50-60Hz OR 170-264VAC @ 50-60Hz |
| Operating Temp. | 0-70 degrees Celsius |
| Weight | Approximately 8.5lbs |
| Width | Height | Depth | |
| Dimensions | 8.5 " | 5.5 " | 5.5 " |
| Name | Format | Link |
| User Manual |  |
| Type | Name | Description | Link |
| Standard Product | PM Kit | PM Kit includes strain gauge sensors, cables and mounting hardware |
 |
| Standard Product | Resolver | Precise crank-angle position measurements |
|
| Standard Product | PressNet | Networking software that provides detailed production and tonnage information |
|
| Standard Product | TT-Graph | Signature analysis program that generates tonnage signatures and provides a simple approach for analyzing the signatures |
|
| Service | Installation | On-site product installation |
|